By December 8, 20170 Comments Read More →



Yogyakarta/ Semarang/ Solo | 18 – 19 Desember 2017 | Rp. 6.900.000 Per Peserta
Bandung/ Jakarta/ Surabaya | 18 – 19 Desember 2017 | Rp. 7.900.000 Per Peserta
Bali/ Batam/ Balikpapan/ Manado/ Lombok | 18 – 19 Desember 2017 | Rp. 8.900.000 Per Peserta
Yogyakarta/ Semarang/ Solo | 27 – 28 Desember 2017 | Rp. 6.900.000 Per Peserta

Jadwal Training 2017 Selanjutnya …




This course is an integral part of the programme, has a duration of few days, and covers equipment driven directly by gas turbines or indirectly through gas turbine driven generator sets, electrical power systems and motor drivers. Typical applications are for Oil, Gas and other industries


  1. Gas Turbine Engines
    The basic principles underpinning the operation of the gas turbine will be presented. This section will also include a description of the following cycles:- simple, reheat, recuperated, inter-cooled, combined gas and steam and steam injected. The effects of engine rating, variation in efficiencies between engines, maintenance intervals and fuel quality are introduced.
  2. Pumps and Compressors
    The basic principles of rotor dynamic and positive displacement pumps and compressors and the effects of cavitation, compressibility, viscosity variation and humidity. Losses in fluid systems and interaction between machines and systems. Introduction to the basic design principles of pumps and compressors, involving shafts, bearings and seal systems. A discussion of the regulation of pumps and compressors. The correct selection and application of pumps and compressors.
  3. Electrical Power Systems
    Power System Design covering voltage and frequency control, maximum and minimum system fault levels. A demonstration of power system simulation by computer studies including load flow, voltage drop, short circuit levels, motor starting performance and protection grading.
  4. Electrical Power Generation
    An overview of the electrical features of power generation. The mechanical engineer is involved as a member of a design team, often as the lead engineer, with the important requirement of discussing electrical design features with specialist engineers and then being expected to take part in the decision making process for a power generation package. Design, construction and specification of synchronous machines (generators) with typical data sheets.
  5. Electric Motors Drive Systems
    Design and construction features of asynchronous machines (motors), load characteristics, active and reactive load sharing, power transfer between power systems. Matching motors to the driven equipment and effect of power supply system variations. Specifications in relation to IEC/BSS standards. Data sheets for the selection and purchase of electrical machines. Electrical Variable Speed Drive Systems with power electronics and various types of convertors, applications to motors and generators, effect on driven equipment. Data sheets for the selection and purchase of systems.
  6. Aspects of Electrical Machines
    Hazardous area protection, electrical power three phase calculations with worked examples and typical values that can be used during project evaluations. Operation and Maintenance plans and common failures. Digital microprocessor systems interfacing with plant control systems for the control, protection and retained information on motor performance.
  7. Selection of Drivers
    When driving rotating equipment a key aspect of any project is the decision on whether pumps or compressors are to be driven by gas turbine engines or by electric motors from a power system with the option of local gas turbine driven power generation. Each project will always have its own particular solution.

Design Workshop

Workshop exercises in which machines are chosen to meet an outline brief for a pump or compressor plant with the appropriate direct or electric motor drive and its control system will be undertaken.



Jadwal Training 2017

  • Waktu  Dan Tempat
  • Hotel Santika Kuta, Bali
  • Hotel Nagoya Plaza, Batam
  • Hotel Fave, Balikpapan
  • Hotel Aston, Manado
  • Hotel Lombok Raya, Mataram
  • Hotel Serela Merdeka, Bandung
  • Hotel Santika Pandegiling, Surabaya
  • Sofyan Hotel Betawi, Jakarta
  • Hotel Ibis Solo
  • Hotel Ibis Simpang Lima, Semarang
  • Hotel Ibis Malioboro, Yogyakarta
  • 11 – 12 Desember 2017
  • 18 – 19 Desember 2017
  • 27 – 28 desember 2017

Investasi dan Fasilitas

  • Rp 8.900.000 (Non Residential) untuk lokasi di Bali, Batam, Balikpapan, Manado atau Lombok
  • Rp 7.900.000 (Non Residential) untuk lokasi di Bandung, Jakarta atau Surabaya
  • Rp 6.900.000 (Non Residential) untuk Lokasi Solo, Semarang atau Yogyakarta
  • Quota minimum 2 peserta
  • Quota minimum 3 peserta ( Untuk Manado, Balikpapan dan Lombok Quota minimal 4 peserta)
  • Fasilitas : Certificate,Training kits, USB,Lunch,Coffe Break, Souvenir
  • Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel khusus bagi perusahaan yang mengirimkan minimal 3 orang peserta)


Tugino, ST., MT


Share and Enjoy: These icons link to social bookmarking sites where readers can share and discover new web pages.
  • MisterWong
  • Y!GG
  • Webnews
  • Digg
  • StumbleUpon
  • Reddit

About the Author:

Post a Comment