By August 12, 2015 0 Comments Read More →


Yogyakarta | 08 – 11 September 2015 | IDR 9.750.000
Jakarta | 06 – 09 Oktober 2015 | IDR 9.750.000
Bandung |  24 – 27 November 2015 | IDR 9.750.000
Bogor | 15 – 18 Desember 2015 | IDR 9.750.000



Internal Corrosion Problems in Gas, Oil and Produced Water Pipeline and Equipment

  • Piping and Pipeline Leakage due to Pitting Corrosion and Microbiological Induced Corrosion
  • Severe Pipe Wall Thickness Reduction and Short Remaining Service Life caused by Sour Corrosion
  • Pipe Wall, Rotating Parts and Equipment Cracking due to Chloride and Sulfide in the Fluids
  • Internal Corrosion of Pipeline and Equipment due to Water in Oil and Oil in Water Emulsions
  • Internal Corrosion due to Multi Phase Flow in the Pipeline
  • Severe Corrosion Rate caused by CO2 and Hydrate in the Gas Lines, CO2/H2S Removal Unit and Glycol Dehydration Unit
  • Internal Corrosion in the Water Lines due to Dissolved Oxygen, Mud and Sludge
  • Malfunction of Pump, Compressor, Valves and Equipment due to Under-Deposit Corrosion, Under-Film Corrosion and Fouling

The Nature, Mechanism and Characteristics of Internal Corrosion and the Control Methods

  • Anodic-Cathodic Reactions, Electrical Properties and Characteristics of Corrosion Cells
  • Physical & Metallurgical Conditions of Metals and Chemical Composition that Promote Corrosion
  • Destructive and Catastrophic Effects of Corrosive Agents and Microorganism in the Gas, Oil and Produced Water Fluids
  • The Role and Mechanism of O2, CO2, H2S, Dissolved Salts and Microorganism in Internal Corrosion
  • The Role of Oilfield Bacteria and the Mechanism of MIC
  • Characteristics and Detection of Internal Corrosion in the Pipeline and Surface Equipment
  • Removal of Dissolved Corrosive Agents and Non-Hydrocarbon Gases in the Gas, Oil and Produced Water Fluids
  • Internal Corrosion Control with On-line Chemical Inhibitors Injection, Surface Barriers and Scavengers

Internal Corrosion Detection and Monitoring  Techniques, Devices and Analysis

  • Visual Inspection and Early Detection Techniques & Devices for Monitoring Fluid Corrosiveness and Tests for Identifying Corrosion products
  • The Important of Internal Corrosion Rate Monitoring Before and After Chemical Injection and Treatment
  • NACE Standard Method for Preparation, Installation, Laboratory Analysis and Interpretation of Results of Internal Corrosion Monitoring
  • Access Fittings, Retrievers, Corrosion Coupons, Scale Coupons, Corrosion Probes,  Holders, Injection & Sampling Devices and Instrument for On-line Internal Corrosion Monitoring
  • The Use of Nipple or Spool, Hydrogen Probe and Galvanic Probe
  • NACE Standard Method for Testing and Analysis of Bacterial Activity and Microbiological Induced Corrosion
  • Iron Content Analysis of Produced Water and the COPRA Correlation
  • Down-hole Tubing or Casing Calipers, Ultrasonic Wall Thickness Testers and Radiography

Internal Corrosion Control with Chemical Inhibitor Injection, Passive Film Formation and Biocides

  • Nature & Classification of Inhibitors and Effect of Ionic Character on
  • Inhibiting Ability
  • Formulations of Oilfield Inhibitors and the use of Water Soluble Inhibitors, Volatile Inhibitors and Acid Inhibitors
  • Typical Corrosion Inhibitors, Scavengers & Biocides for Oil & Gas Field
  • Guidelines of Inhibitor and Biocide Applications and the Chemical Injection Equipment for Pipeline and Surface Facility
  • Inhibitor and Biocide Batch Treatment Using Pigs, Chemical Dosage and the Pigging Operations
  • Surfactant and Cleaners for Solving Fouling Problem in the Equipment and Systems
  • Cationic & Mixed Charge Organic Inhibitors for Hydrocarbon and Oxygen Corrosion Inhibitors for Produced Water
  • Testing and Evaluation of Inhibitor and Biocide Effectiveness
  • Safety Precaution in Working with Inhibitors and Biocides

Internal Corrosion Control as a Key Factor to Pipeline Integrity Management

  • Hazard Assessment and Risk Based Inspection for the Pipeline and Equipment Maintenance Program
  • Pipeline Internal Damage Record and Wall Thickness Monitoring
  • Pigging for Water and Deposit Removal from the Pipeline System
  • Controlling of Flow Stability and Corrosion Rate to a Safe Level
  • Estimating Present Pipeline Remaining Service Life
  • Evaluation of Present Condition and Comparison with Initial Pipeline Design Baseline
  • Evaluation and Controlling of Chemical Inhibitor and Biocide Injection by using Corrosion Rate Monitoring Data.
  • Evaluation of Pipeline and Equipment Damage in accordance with Root Cause Failure Analysis
  • Development of Specific Pipeline Integrity Management System by using Internal Corrosion Rate Monitoring Data

Course Leader: Hilman Ahmad

This specially designed course will be conducted by Hilman Ahmad & Associates, an Independent Consultant in industrial oil and gas, member of the Society of Indonesian Petroleum Engineers, who manage the Professional Industrial Oil & Gas Education Center, and has been practicing production operation & safety and corrosion control engineering in Indonesia for more than twenty-five years. He post-graduated from Tokyo Institute of Technology (sponsored by UNESCO) in 1977. He joined in-field-practice program at Nippon Kokan Steel Company & Research Center Kawasaki, Japan for production facility design & construction and corrosion prevention & control in 1983, and collaborated with Cormon Industrial Research Center Brighton UK for on-line corrosion monitoring development in 2000. He has been delivering training course in production operation, maintenance & safety and corrosion control for personnel from Oil & Gas Company and Petrochemical Industry since 1979.

General Information

Certificate of Appreciation

All attendees will receive a certificate of appreciation attesting to their participant in the internal corrosion training. This certificate will be providing in exchange for a completed training questionnaire.


  • Quality training material kits will be on registration, additional papers, & handouts assignment by Our Partner.
  • Note-taking by participants is encourage. However, to ensure free and open discussions, no formal records will be kept.

Dress Code

Casual clothing is recommended. The internal corrosion training atmosphere is informal.


  • Qualified instructor
  • Quality Training Material (hardcopy and softcopy)
  • Quality Training Kits included Calculator, T-shirt, or jacket,or cap etc.
  • Interactive Presentation with discussion
  • Convenient Training Facilities with four(4) stars quality
  • Lunch per Day
  • Morning and Afternoon coffee/ tea breaks for along the internal corrosion training
  • Certificate of Completion
  • Executive flash disk , Stationery , Note book , exclusive bag .
  • Foto Training Internal Corrosion
  • Training room with full AC facilities and multimedia



  • Yogyakarta, 26 – 29 Mei 2015
  • Jakarta, 2 – 5 June 2015
  • Bandung, 28 – 31 Juli 2015
  • Bogor, 4 – 7 Agustus 2015
  • Yogyakarta, 8 – 11 September 2015
  • Jakarta, 6 – 9 Oktober 2015
  • Bandung, 24 – 27 November 2015
  • Bogor, 15 – 18 Desember 2015

Tuition Fee & Registration  Deadline

  • IDR 9.750.000,-/ Person
  • Registration deadline a weeks before training held.

Minimum Participant

Internal Corrosion training will be conducted if we receive registration letter from 3 (three) participants (Minimum)

Share and Enjoy: These icons link to social bookmarking sites where readers can share and discover new web pages.
  • MisterWong
  • Y!GG
  • Webnews
  • Digg
  • StumbleUpon
  • Reddit

About the Author:

Post a Comment